|Standard:||EN50618-2014||Specifications:||Wires And Cables Up To 3KV.|
|Net Weight:||25kg And B Component Is 5kg||Environment:||Clean, Dry And Ventilated Warehouses|
coax cable connectors,
tv coaxial cable connectors
|125℃ Self-cross linking LSZH FRPolyolein Cable Compound
|ZC-SC125P is a self-crosslinking low smoke zero halogen flame retardant polyolefin cable compound, which can be naturally cross-linked after being extruded into a cable. This product is mainly used for the sheath and insulation of photovoltaic cables that comply with TUV2Pfg-1169 and EN50618.|
|High temperature resistance XLPO Compound for wires and cables up to 3KV.|
|Density||g/cm3||GB/T 1033||ISO 1183-1||┄||1.40|
|Tensile strength||Mpa||GB/T 1040.2||ISO 527-2||≥10.0||13.5|
|Elongation at break||%||≥150||250|
|%||GB/T 2951.12||IEC 60811-1||±25||+12|
|Volume resistivity (20℃)||Ω·m||GB/T 1410||IEC 60093||≥1.0x1012||2.6x1012|
|Volume resistivity at operating temperature (125±2℃)||Ω·m||┄||┄||≥2.0x108||3.5x108|
|Dielectric strength||MV/m||GB/T 1408.1||IEC 60243-1||≥20||25|
|Brittleness temperature (-40℃)||℃)||GB/T 5470||ISO 974||Pass||Pass|
|Oxygen index||%||GB/T 2406.2||ISO 4589-2||≥28||35|
|non-luminous flame||GB/T 8323.2||ISO 5659-2||≤350||310|
|HCl and HBr content||%||GB/T 17650||IEC 60754||≤0.5||0|
|NOTE: (1)The toxicity of smoke produced by materials shall be negotiated by both the supplier and the demander
according to the needs of the product application.
It is recommended to use a low smoke zero halogen special screw, with a length to diameter ratio of L/D=20~25 and a compression ratio of 1.1~1.3. Because the actual temperature of the melt is related to the length diameter ratio, compression ratio and screw structure of the extruder, the appropriate extrusion temperature should be selected according to the specific situation of the extruder.
The recommended setting temperatures for each zone of the extruder are as follows:
|(1)When using this product, mix the A and B components evenly and drop them into the hopper.
If color is required, the cable factory can use polyethylene base color masterbatch and materials
within 8 hours after unpacking.
(2)This product should not be shut down for a long time. If it is shut down for a long time, it is
recommended to stop and clean the screw before starting up again.
(3)To ensure sufficient crosslinking of the material, it is recommended that the cable be placed in
a 70°C water bath or steam room for 6~8h, or at a constant temperature and humidity (23°C, 50%)
for 7 days. The specific placement time is adjusted according to the thickness of the product and
the crosslinking degree of the material, so as to meet the performance requirements of the cable.
|Package.Storage and Transport:|
|Package||Net weight||The A and B component are kept in different bags, net weight of
A component is 25kg and B component is 5kg
|Method||Aluminum foil/polyethylene complex film bag for inner+ PP woven bag/
PE/Kraft paper bag for outer
|Transport||Requirement||Keep away from the sunshine, rain and soaking during transport, as well
as handle gently during carrying.
|Storage||Environment||clean, dry and ventilated warehouses|